In this well-known clip, water pours from a hose and, on camera, seems to hang in the air as a frozen wave, then crawl back upward, then drift down in slow motion. Nothing magical is happening to the water. A speaker is shaking the hose at a precise frequency, and a video camera that records 24 frames per second samples the stream at almost exactly the same rhythm. The result is a camera illusion called the stroboscopic effect, and you can recreate it at home with a speaker, a garden hose, a tone generator and a camera that shoots at 24 fps.
The video was made by the YouTube creator brusspup, who published it in March 2013 as a second, better-lit attempt at an experiment he had first filmed a year earlier. Below we explain what you are actually seeing, why the numbers 23, 24 and 25 matter, and how to set the experiment up without frying your electronics.
What the sound and water experiment really shows
A speaker cone moves back and forth when it plays a tone. A 24 Hz tone is a very low hum, close to the bottom of human hearing, and it makes the cone move 24 times every second. If a soft rubber hose is taped firmly against the speaker, the hose shakes at that same rate.
Water leaving a shaking hose does not fall in a straight line. Each little burst leaves the nozzle while the hose is slightly to the left or slightly to the right, so the falling stream takes on a regular zigzag or spiral shape. To your eye, that shape is moving downward far too fast to follow, so you see a blurry, wobbling stream.
The camera sees something different. It does not watch continuously; it takes 24 separate pictures every second. When the hose vibrates 24 times per second, every picture catches the stream at the same point in its cycle. Frame after frame, the wave looks identical, so on playback the water appears to be standing still in mid-air.
Why a few hertz make the water flow backwards
This is the same illusion that makes car wheels and helicopter rotors appear to spin slowly, stop or turn backwards in films. Physicists call it the stroboscopic effect, a form of aliasing: a fast repeating motion is sampled at a rate close to its own, and the brain stitches the samples together into a slow, false motion.
Here is how it plays out with the hose:
- 24 Hz tone, 24 fps camera: each frame catches the wave in exactly the same position. The water looks frozen.
- 23 Hz tone: the hose completes slightly less than one full cycle between frames. Each new picture shows the wave a little behind where it was, so on screen the stream seems to climb back up into the hose.
- 25 Hz tone: the hose completes slightly more than one cycle between frames. Each picture shows the wave a little further along, so the water appears to fall in gentle slow motion.
The same rule works for any frame rate. If your camera or phone records at 30 fps, use a 30 Hz tone to freeze the stream, 29 Hz to reverse it and 31 Hz for slow motion. At 60 fps, try 60, 59 and 61 Hz, although very low-frequency hums are easier for small speakers to reproduce cleanly.

The basic set-up: a soft hose taped against a powered speaker, with the camera fixed on the falling stream.
What you need for the experiment
- A powered speaker, ideally one with a decent woofer that can reproduce low bass
- A water source, such as an outdoor tap or a sink
- A soft, flexible rubber hose (stiff tubing does not pass on the vibration as well)
- Tone-generator software or a free tone-generator app, plus a cable from your computer or phone to the speaker
- A camera that can record at a fixed 24 fps (or a known frame rate you can match)
- Tape, or a strap, to hold the hose against the speaker
- Strong light, and something waterproof to protect the speaker
How to set it up, step by step
1. Attach the hose to the speaker
Lay the hose down the front of the speaker so it presses against the cone or the grille directly over it. Let a short length, roughly 2.5 to 5 cm (one or two inches), hang free below the speaker. That loose end is what whips back and forth. Tape it securely: if the hose is only resting near the speaker, the vibration will not transfer and the stream will barely move.
2. Fix the camera settings
Switch the camera to 24 fps and lock the settings manually if you can. A fast shutter speed gives crisp droplets instead of a smeared stream, but it lets in less light, so the faster you go, the brighter your scene needs to be. Outdoors in sunlight or with a strong lamp behind or beside the water works best. A dark background makes the water stand out.
3. Play the tone and turn on the water
Start the 24 Hz tone, then open the tap gently. Too much pressure makes a thick, chaotic stream; a moderate flow gives the clearest wave. Watch the camera screen rather than the water itself, because the effect only exists in the recording. Then nudge the frequency down to 23 Hz or up to 25 Hz and watch the stream reverse or slow down.
4. Fine-tune
Cameras are not always exactly 24 fps; many record at 23.976 fps. If the frozen wave slowly drifts, adjust the tone in small steps, such as 0.1 Hz at a time, until it holds still. Increasing the volume makes the wave bigger; decreasing it makes it subtler.
Can you see the effect without a camera?
Not with this exact set-up. Your eyes do not take separate snapshots the way a camera does, so in the room you simply see a vibrating, blurry stream.
You can see a version with the naked eye if you replace the camera with a strobe light. A strobe flashing 24 times a second, matched to a 24 Hz tone, lights the water only at the same point in each cycle, and the droplets appear to hang in the air. This is how "levitating water" fountains in science museums work. Shift the strobe or the tone by a hertz or so and the drops seem to rise or sink slowly.
One caution: rapidly flashing lights can trigger seizures in people with photosensitive epilepsy, so warn anyone nearby before using a strobe.
Safety tips and common mistakes
- Keep water away from electricity. Wrap the speaker in a thin plastic bag, keep the amplifier and computer well away from splashes, and use an outlet protected by a residual-current device (GFCI) if you are working outdoors.
- Do not push the volume too hard. Very low frequencies at high volume can damage small speakers. Raise the level slowly.
- Use a tripod. Any camera shake ruins the illusion, because the frozen wave will appear to bounce.
- Check your frame rate. Some phones change frame rate automatically in low light. Lock it if your camera app allows.
Is this "the power of music"? Separating the science from the myths
Videos like this are often shared with captions about the mysterious power of sound or music over water. The experiment is a genuinely good demonstration of physics, but it does not show that sound changes the nature of water. The tone simply moves the hose, and the camera's frame rate does the rest. You could get the same picture by shaking the hose with a motor running at 24 cycles per second, with no sound at all.
Sound can create striking visible patterns, and that field has a long history. In the 18th century the German physicist Ernst Chladni sprinkled sand on vibrating plates and recorded the shapes it formed, now called Chladni figures. In the 1960s the Swiss physician Hans Jenny coined the word "cymatics" for the study of such patterns. Those shapes are explained by ordinary physics: the size, shape and fixing points of the vibrating surface decide where the sand collects.
Some films go much further. The 2009 documentary Kymatica, often quoted alongside this video, argued that sound is "something more than mere vibratory signals" and that it sustains and shapes life itself. That is a philosophical idea rather than a finding backed by evidence, and the water experiment does not test it. Enjoy the clip for what it is: a clever, repeatable lesson in how cameras sample motion, and how easily our eyes can be fooled.
Sources: Video and original project instructions by brusspup, "Amazing Water & Sound Experiment #2" (YouTube); Wikipedia: Stroboscopic effect; Wikipedia: Cymatics.
Related:
COMMENTS