Originally published 2020-04-29.

Yes, a handheld skin printer for burns exists, but it is still a research device rather than standard hospital equipment. Engineers at the University of Toronto and burn surgeons at Sunnybrook Health Sciences Centre built a small, hand-held tool that rolls a thin, living sheet of "bioink" straight onto a wound. In February 2020 the team reported in the journal Biofabrication that full-thickness burns in pigs treated this way healed with less inflammation, less scarring and less shrinkage than comparison wounds.
That result is encouraging, yet it is one step on a long road. Below we explain what the device does, why burn surgeons want something like it, what the pig study actually measured, and what still has to happen before a patient in a burn unit could be treated with it.
Why deep burns are so hard to close
Skin has two main layers. The thin outer epidermis is the waterproof barrier, and the thicker dermis beneath it holds blood vessels, nerves, hair roots and the collagen that gives skin its strength. A superficial burn damages only the top layer and usually heals by itself. A full-thickness (third-degree) burn destroys both layers, so the body has no local cells left to rebuild from.
For decades the main answer has been the autologous skin graft: surgeons remove the dead tissue, shave a thin slice of healthy skin from somewhere else on the patient, often the thigh, and fix it over the wound. Grafts work well, but they create a second wound at the donor site. When burns cover a large share of the body, there may simply not be enough healthy skin to harvest. That shortfall is exactly the gap the Toronto group set out to fill.
Other options exist. Lab-grown skin substitutes and collagen-based "scaffolds" can cover a wound while the body repairs itself. They help, but they can be expensive, may take weeks to prepare and do not always integrate well, so surgeons are still looking for faster, more flexible tools.
How the handheld printer works
Most 3D bioprinters are large benchtop machines that build tissue layer by layer in a lab, which then has to be transported and attached to the patient. The Toronto device takes the opposite approach and brings the printing to the bedside. It is about the size of a shoebox and is guided across the wound by hand.
Senior author Axel Günther, a mechanical engineer at the University of Toronto, compared it to a tape dispenser in a 2018 interview with Smithsonian Magazine, describing a microdevice that "squishes out a piece of tissue tape". A soft roller at the front lays down a continuous strip of material, and the operator overlaps strips to cover a wound of almost any size or shape.
That strip is the bioink. In the 2020 version it is based on fibrin, the protein that forms a natural blood clot, and it is loaded with mesenchymal stromal cells (MSCs). MSCs are not skin cells. Their value lies in the signals they release, which calm inflammation and encourage the patient's own tissue to grow back into the area. The bioink gels within moments, so it stays where it is placed.
Built for real wounds, not flat dishes
A key design goal was handling curved and sloping surfaces. Burns wrap around arms, legs and torsos, and an earlier prototype struggled on anything but level ground. The improved device was tested specifically on its ability to lay an even layer on inclined surfaces, which matters if it is ever to be used on a patient lying in a hospital bed.
What the pig study found
Pigs are a standard model for burn research because their skin is structurally closer to ours than that of rodents. The researchers created full-thickness burns and compared three groups: wounds left untreated, wounds covered with a commercial collagen scaffold, and wounds covered with MSC-loaded sheets from the handheld printer.
- Placement: the sheets went on evenly and stayed in place with very little shifting.
- Healing quality: wounds treated with MSC sheets showed less inflammation, less scarring and less contraction than both comparison groups.
- Practicality: the procedure was fast and did not require a separate lab-grown graft.
Co-author Marc Jeschke, a burn surgeon then at Sunnybrook's Ross Tilley Burn Centre, summed up the headline result in the IOP Publishing press release: "Most significantly, our results showed that the MSC-treated wounds healed extremely well."
Wound contraction deserves special mention. When large burns heal, the new tissue tends to pull tight, which can restrict movement at joints and sometimes needs later surgery. Any treatment that limits contraction could make a real difference to long-term quality of life.
What the device does not do yet
Headlines often described the invention as "printing new skin". That overstates it. The sheet is a temporary, cell-rich covering that supports the body's own repair; it is not a complete, fully formed skin with hair follicles, sweat glands and pigment. It also has not replaced the skin graft. The researchers see it as a way to help when grafting is limited or impossible.
The study was carried out in a small number of animals, and good results in pigs do not guarantee the same outcome in people. Human trials must show that the method is safe, that the cells behave as expected, that infection risk is controlled and that results last. Günther himself said in the press release that further study is required, while calling the early signs promising.
There are also practical questions. Where would the stromal cells come from? Could they be stored and shipped ready to use? Would the device fit into the tight time window of early burn surgery? Each of these must be answered before regulators would approve routine use.
Where bedside bioprinting fits in burn care
The Toronto device is part of a wider push toward "in situ" bioprinting, meaning printing tissue directly on or in the body instead of in a lab. Other groups have experimented with robotic arms and scanners that map a wound and spray cells onto it, and with spray-on skin cell suspensions that are already used clinically in some countries for certain burns. A handheld tool has a particular appeal: it is cheaper, portable and easier to bring into an operating room than a large robotic system.
If the approach succeeds in humans, the biggest beneficiaries would be people with burns over a large part of the body, for whom donor skin is scarce. Faster coverage of a burn lowers the risk of infection and fluid loss, which are among the main dangers after a severe injury.
Practical takeaways for readers
- This is promising research, not a treatment you can request today. Burn care still relies on proven methods such as excision and grafting.
- Any serious burn, especially one that looks white, leathery or charred, or that covers a large area, needs emergency medical care. Talk to a doctor or call emergency services rather than treating it at home.
- For minor burns, health services generally advise cooling the area under cool running water for about 20 minutes and covering it loosely. If you are unsure how serious a burn is, ask a doctor.
- When you read about "printed skin", look for the species tested, the number of subjects and whether human trials have started. Those three details tell you how close a technology really is.
The handheld printer is a good example of engineers and surgeons working side by side on a stubborn clinical problem. It has cleared an important animal milestone; the next chapters will be written in clinical trials.
Sources: IOP Publishing press release (February 2020); Biofabrication: the pig study; Smithsonian Magazine (2018).

COMMENTS