
How drafting worked before AutoCAD
Before computer-aided design, every building, car, aircraft part and power station started as a pencil drawing on paper. Companies employed whole rooms of draftsmen and draftswomen who turned engineers' and architects' ideas into precise, measured drawings that workshops and builders could follow. The photographs below show those rooms, from pre-war engineering offices to the bright open-plan halls of the 1960s and 1970s.
The change came with AutoCAD. Autodesk released it in December 1982 for CP/M and IBM PC computers, and by March 1986 it had become the most widely used CAD program in the world. Earlier CAD systems, going back to Ivan Sutherland's Sketchpad in 1963, needed expensive mainframes or minicomputers, so big firms such as carmakers and aerospace companies were the first to use them. AutoCAD put drafting software on an ordinary desktop computer.
What strikes most viewers is the sheer scale. A full-size or large-scale drawing needed a big flat surface, and each drafter needed room to reach every corner of it. That is why these offices look like aircraft hangars filled with tables.
The tools on every drafting table
The basic kit barely changed for a century. Paper or film was taped to a smooth drawing board with straight, square edges. A T-square slid along the edge to give perfectly parallel horizontal lines, and plastic or wooden set squares rested on it for vertical and angled lines. Compasses drew circles and arcs, French curves handled freer shapes, and templates sped up repeated symbols.
Many of the photos show the next step up: the drafting machine, a hinged arm mounted on the board that holds two rulers at a fixed right angle anywhere on the sheet. Because it is fixed at both ends, every line drawn along it stays parallel, and the head can be turned to any angle, which made separate triangles unnecessary. Drafters also had to master neat hand lettering, since every note and dimension was written by hand.
The hardest part was change. Fixing a mistake or updating a design could mean erasing carefully, or redrawing the sheet entirely. That is the real advantage of 2D CAD: Wikipedia's article on technical drawing calls it "merely an electronic drawing board", but one where revisions are fast and copies are perfect.
Inside the great drafting rooms

This is the full version of the opening picture: rows of men in white shirts and ties leaning across enormous tables, with rolled drawings lying beside them. The photo is widely shared with the caption "General Motors Technical Center in Warren, Michigan". The size of the tables suggests large-scale car body or component drawings.

A colour photo of a smaller room with a blackboard, drafting machines clamped to every table and young people at work. It is often captioned as a drafting class from the early 1970s. Technical schools taught these skills for decades as a standard route into engineering work.

A huge black-and-white hall under long rows of hanging lamps, with angled boards and drafting machines stretching into the distance. In the foreground a man in a white shirt works on a sheet laid flat on a table. The print carries an archive number in the corner, a sign that it came from a company or agency photo collection.

An older, more formal office with arched windows, wooden desks and men in waistcoats and white shirts. A supervisor in a dark suit stands among the tables as others bend over their work. The clothing suggests the 1920s to 1940s, when drafting offices were largely male.

A colour photo of draftsmen in grey work jackets seated at steep drawing boards fitted with drafting machines and lamps. It is shared online as Tamron's drafting department in the late 1970s, the Japanese company known for camera lenses. Upright boards like these let drafters see the whole sheet without leaning over it.

Rows of heavy desks fill a long room lit by fluorescent tubes, with each drafter facing the same way like pupils in a school. The marking "1-42" in the corner may point to January 1942, during the Second World War, when engineering offices expanded quickly. Rolled sheets and reference papers are piled on almost every desk.

Draftsmen in white coats stand at nearly vertical boards, each fitted with a sliding parallel rule. In front, a man draws a detailed floor plan in red and black, with a scale ruler beside him. The near-vertical boards kept the whole sheet in view.

An industrial hall with a curved, beamed roof and dozens of lamps hanging on long cables. Some drafters stand at high tables while one in the foreground uses a long straightedge across a large sheet. Hanging lamps let each drafter bring light close to the sheet.

A closer crop of the office photo seen earlier with the "1-42" marking. Here the faces are clear: men in shirts and ties, one in an apron, smiling as they work at sloping desks with drawings rolled up in front of them. The numbers stencilled on the desks helped track who worked where.

A crowded office with numbered pillars and tall windows, where dozens of men in suits, waistcoats and ties look up from their tables. Rolled drawings lean against desks and walls. The style of dress points to the early decades of the twentieth century.

Draftsmen lie and kneel on padded cushions on top of a giant drawing surface that runs the length of the room. Work at this scale was usually a full-size layout, for example of a ship, aircraft or vehicle part, where the drawing had to match the real object exactly. It shows how physical drafting could be.

A bright mid-century office with long flat tables, steel cabinets and men in white shirts, one wearing glasses and a bow tie. Each table holds a sheet as big as the drafter's arm span. The relaxed poses suggest a working day rather than a staged photo.

An enormous open-plan room where rows of upright boards stretch away under a high ceiling. Drafters sit at flat tables in front and stand at the vertical boards behind. It gives a sense of how many people one large engineering project once needed.

A smaller studio with exposed brick, poles for lamps, and drafters sitting on high stools at tilted boards. The clothes and hairstyles suggest the late 1960s or 1970s. The cramped space is a contrast to the giant corporate halls.

A bright hall lit by skylights, with drafting machines mounted on wooden tables and coats hanging on stands by the windows. Men and women work side by side here.

Rows of wooden tables under a timber roof, with dozens of men in waistcoats looking toward the camera. The handwritten caption on the print appears to identify it as the drafting room of the engineering department of the Southern California Edison Company. Electric utilities needed constant drawings of power plants, lines and substations.

Two men lie flat on a huge sheet spread over the floor, drawing what looks like a street plan or map. The photo circulates as a picture of urban designers at work. At this size, the only way to reach the middle of the drawing was to climb onto it.

A quieter colour photo from what looks like the 1970s, with green walls, yellow blinds and drafting machines on every table. A single draftsman sits at his board while the rest of the room is empty. Within a decade or two, many rooms like this would be refitted with computer terminals.

Long rows of upright boards with drafting machines, adjustable lamps and telephones. A sign at the end of a row is written in a Scandinavian language and appears to be a list of rules for the office. Upright boards also took up less floor space than flat tables.
What former drafters remember
When the photos were shared online, people who had worked in these rooms added their own memories. A selection of their comments is below.

One former draftsperson recalls that every drafter had a personal style, almost like a signature, and remembers a colleague who hid a tiny mouse in all his drawings. Hidden signatures like this were a small way to leave a personal mark on technical work.

Another commenter describes a career that moved from pen and ink to AutoCAD and then to SolidWorks. That path, from hand drawing to 2D CAD and then to 3D modelling, matches the way the whole profession changed.

A drafter who started in 1982, just as AutoCAD arrived, says hand drafting felt more like an art. She contrasts it with later pressure to turn out drawings at high speed once computers became standard.

A designer who learned AutoCAD in the late 1980s says he still prefers drawing by hand for his own designs. Many architects and designers still sketch on paper first and move to software later.

A commenter who worked for an architect loved watching him draw by hand because he still worked the old way. The comment shows how much a well-made hand drawing could impress the people around it.

A former high-school drafting student says he would prefer the manual method to computers, calling it more rewarding mentally and physically. Technical drawing was long a school subject in many countries, and it is now usually taught with CAD software.
What changed, and what did not
Computers made drawings faster to revise, easier to copy and simpler to share. 3D programs such as SolidWorks went further: the designer builds a digital model first, and the 2D views are generated from it, so the software can check whether parts fit before anything is made.
The knowledge behind the drawing stayed the same. A drafter still needs to understand projections, tolerances, materials and how a part will actually be built. The rooms got smaller and quieter, but the skill these photos show, turning an idea into exact instructions, is still the heart of engineering and architecture.
Sources: photos via Design You Trust and Vintage Everyday; captions cross-checked with Rare Historical Photos; AutoCAD (Wikipedia); Technical drawing (Wikipedia).

COMMENTS